Switch Hikvision 4p Poe Smart 2uplink 60w Ds-3e1106hp-ei

Descripción

GENERAL
Carcasa Metal material, IP40
Peso Neto 0.245 kg (0.54 lb)
Peso Bruto 0.645 kg (1.42 lb)
Dimensiones (W X H X D) 145.0 mm × 25.6 mm × 68.45 mm (5.7" × 1.0" × 2.69")
Temperatura De Funcionamiento 0 °C to 40 °C (32 °F to 104 °F)
Temperatura De Almacenamiento -40 °C to 85 °C (-40 °F to 185 °F)
Condiciones De Humedad 5% to 95% (no condensation)
Humedad Relativa 5% to 95% (no condensation)
Fuente De Alimentación 48 VDC, 1.35 A
Modo De Instalación Desk-Mounted, Wall-Mounted
Max. El Consumo De Energía 65 W
Consumo De Energía En Inactivo 2 W
Surge Protection 6 KV

PARÁMETROS DE RED
Puertos 4 × 10/100 Mbps PoE port, 2 × 10/100 Mbps RJ45 port
Tabla De Direcciones MAC 2 K
Capacidad De Conmutación 1.2 Gbps
Tasa De Reenvío De Paquetes 0.90 Mpps
Caché Interna 768 Kbits

FUENTE DE ALIMENTACIÓN POE
PoE Standard IEEE 802.3af, IEEE 802.3at, IEEE 802.3bt
Pin De Alimentación PoE 8-pin power: 1/2(-), 3/6(+), 4/5(+), 7/8(-)
Puerto PoE
Hi-PoE: Port 1
PoE: Ports 2 to 4
Max. Puerto De Alimentación 60 W, 30 W
PoE Power Budget 60 W

FUNCIÓN DE SOFTWARE
Largo Alcance
Ports 1 to 4: up to 300 m.
Long range performance may vary depend on camera model or cable condition.
VIP Port Ports 1 to 2: data on VIP ports is preferentially forwarded when bandwidth resources are insufficient.
PoE Watchdog Ports 1 to 4: auto detect and restart the cameras that do not respond.
Port Isolation/HPP
Support one-click activation and remote management via Hik-Partner Pro. Functions supported:
1. Display the port rate.
2. Display the port bandwidth utilization rate.
3. Display the PoE power usage.
4. Display topology information.
5. Display the alarm status.
6. Restart ports and devices.
7. Enable port long-range mode.
8. Remotely upgrade the device.
Link Aggregation/

SYSTEM MAINTENANCE
Support device management via web.
Support DHCP Client. Enabled by default for dynamic assignment of management IP addresses.
Support Super IP, which is a fixed IP address (10.180.190.200) for direct access.
Support management via Hik-Central Pro.
Support remote management via Hik-Partner Pro.
Support cable detection. Abnormal open circuits and short circuits as well as network cable length can be detected.
Supports 802.1ab LLDP for peer device discovery.
Support SNMP v1/v2c for third-party management platform access.
Support port mirroring for fault locating.
QoS/Storm Control
Storm control is used to prevent switch ports from being blocked by broadcast or multicast storms in the LAN, which may affect network communication.
Supports port rate limiting based on broadcast, multicast, and unknown unicast packets.
DHCP Snooping
DHCP Snooping can prevent unauthorized connections to DHCP servers from disrupting the network and affecting normal network communication, and only allow DHCP packets from trusted ports to pass through.